Floor lamp is how to choose and buy and maintenance

Floor lamp purchase points, photogenic type floor lamp pay attention to the height; When purchasing a photogenic type floor lamp, want to consider factors such as the height of the smallpox, to 1. 70 m - 1. 80 meters high floor lamp, for example, the ceiling height in 2. More than 40 m effect * * better, if the ceiling is too low, the light can only focused on the local area, will make the person feels soft light too bright enough. At the same time, the use of photogenic type floor lamp, ceiling in the home * * good for white or light color, the material of the ceiling good glance has certain effect. Direct according to floor lamp pay attention to the luminosity; Straight floor lamp illuminated when the choose and buy should pay attention to, under the shade along the low * * like eyes, so as not to make eye discomfort with the illuminate of light bulbs. In addition, too much contrast can increase indoor light eyes load, can try to choose floor lamp dimming. When used as direct as light line, * * better avoid reading position near the mirror and glass products, lest cause discomfort reflective. Modelling type floor lamp pay attention to the style; If 'modelling type floor lamp' of choose and buy, the lamp can not used for lighting, it is more in household environment in a 'vulture' light. Of course this kind of floor lamp of choose and buy, want to consider its consistency and household whole style. For example a thick blood stone, establish noble classical lamp and the yuppie style streamlined modern furniture is opposite. Floor lamp installation method 1, before installation to read the installation drawing carefully before installation and floor lamp products instruction, and prepare to install lamps and lanterns of common tools, such as the flat cross screwdriver and a hammer. Disassemble the parts after packaging good * * don't confuse, if similar parts, general installation drawings will draw the object size comparison chart, the unused parts to cross it, very easy to distinguish between various parts. 2, before the installation, check the installation before you check the floor lamp accessories such as all kinds of situation, in case of damage of a floor lamp plate, companies can contact patch. What you want to install wood screws, eccentric shaft, shaft, will be a good guide hole, parts of the positioning problem don't worry about it. Is important to pay attention to that doesn't happen on the wrong parts and then repeated twist together, otherwise easy to damage the plank, installed also often appear the phenomenon such as instability, tilt. 3, installation of floor lamp floor lamp usually there should be a piece of iron chassis, size slightly smaller than the surface of the base, black plastic caps should be used for fixed lampshade fasteners, bottom-up spare parts order should be: chassis fastening nut, cast iron chassis, base, light pole, lamp holder, lamp shade, plastic fasteners, the light bulb. Floor lamp light pole of the power cord through the fastening nut, cast iron chassis, chassis base, and then connect the power cord and with electrical tape, chassis there should be a sunken place the power cord can be stretched out. Floor lamp floor lamp here remind you of the power cord must deal with, such as it electricity safety, 2 will be indoor walking in household is not easy. Floor lamp maintenance tips: 1, moistureproof electrical items * * worry is wet, will not only reduce the service life, there will be electricity is dangerous, so the key to the floor lamp maintenance step is moistureproof, whether it's sitting room place, or the lamp of bathroom, bathroom and kitchen stove headlights, to install good moistureproof lamp shade, prevent moisture intrusion, led lamps and lanterns corrosion damage or leakage short circuit, etc. 2 dust, dust floor lamp maintenance more often, and especially the chimney of floor lamp, lamp shade easy to easily lead to accumulation of ash layer darkening, affect the lighting effect, so often should clean. Clean up the floor lamp shade, with a clean a feather duster sweep off the dust off and gently don't let the chimney deformation. Floor lamp dusting wipe in several ways: ( 1) Common dusting it clean with a clean a feather duster gently can, to be very careful. ( 2) If the floor lamp of non-metallic can use wet cloth to wipe clean, be careful not to rub into the power cord. ( 3) If it is metal lighting with dry cloth is wiped can, don't touch water. Note: when cleaning maintenance must first disconnect the power, at the same time be careful not to alter the structure of lamp act the role ofing, also don't replace the lamp parts, at the end of the cleaning maintenance, should will lighting installed according to the sample, don't packing, wrong installed lighting components, so as not to cause dangerous. At the same time as far as possible can't rinse the lamps and lanterns, as long as can wipe with dry dishcloth touchs water, dry, if accidentally run into water to try to avoid by all means after turn on the light immediately with a damp cloth to wipe. 3, do not frequently switch when using lighting do not frequently switch as far as possible, because the lighting at the instant of the frequent start, through the filament current is greater than the normal work of electric current, the filament temperature rise sharply accelerated sublimation, which will greatly reduce its service life, this is all in the lighting maintenance should pay attention to.